Country homemade their own. Useful homemade products for summer cottages and gardens with your own hands

Interesting homemade products for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, a country shower, a dryer from improvised materials.

Useful homemade products for giving - do-it-yourself washing

Not everyone has the financial ability to buy a Karcher car. If you can't buy it, why not invent it? Homemade car wash allows you to do without running water, reduce water consumption and thoroughly wash the car, fence, garden path or other items.

Here's what you need for such a homemade to give:

• plastic canister with a capacity of 5–20 l;
• hose connector kit;
• automobile nipple;
• piece of hose;
• silicone sealant;
• sharp knife;
• compressor or car pump;
• irrigation gun.

Take a set of hose nozzles, which includes 2 connectors, a 3/4 threaded fitting, a 1/2 adapter.

Here is the principle of operation of such a homemade product for giving: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.

Fill the container with water, but not to the top. Then screw on the lid and pump air in. This will create pressure, and the water will run well when you start to pull the trigger of the gun. Here's how to assemble such a mini sink.

Carefully cut a hole in the lid with the tip of a knife. It should be slightly smaller than the diameter of the nipple stem. Also cut a circle of the desired diameter at the bottom of the sidewall of the canister.

Insert the nipple into the cap.

Now, helping yourself with the wire, place the coupling in the hole intended for it. Apply silicone sealant to secure the coupling to the canister.

It is necessary to tighten the cover and carry out other work only after the sealant has completely cured. Then you will connect one end of the hose to the water gun and the other to the canister.

Pour water into the container, but not to the top so that there is room for pumping air. But do not pump too hard, so that the canister does not deform and burst under pressure. See how the fitting should be screwed in and the connectors installed.

If everything is done correctly, then when you press the trigger of the water gun, the water will spurt out in a good stream. You can adjust the pressure by twisting the tip of the gun.

In the country, it is hardly possible to do without a shower. Try to make something unusual, but tropical, then you can enjoy even more water treatments.

How to make a rain shower from improvised materials for a summer residence?

If you have only recently acquired a plot and you do not yet have a washing room, then you can take a shower right on the street, enclosing a small area near the fence with a curtain. To make such a rain shower, you will need very few components, these are:

• bracket;
• wire;
• flexible hose;
• metal beer can;
• hose adapter;
• awl;
• nails.

Nail the metal bracket onto wooden fence so that the fixture is at the desired height. Screw the adapter to the tip of the hose, fix it on the slot of the beer can. The joint can be treated with a sealant. Using an awl, make many small punctures in the jar.

Tie the top of the hose to the bracket with wire, and attach the other end to a water pipe or pump. When you lower the pump into a barrel of heated water, you will be able to take pleasant water procedures.

You can also make a rain shower head using a disc container. In its center, you need to fix the plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Using an awl, make holes at the top of the lid. Glue all fasteners well with sealant. Such a nozzle is held on the bracket with a thick wire or on a rigid pipe.

If you have a desire to make a rain shower, then you can use plastic pipes for this.

You need to bring water to them, first make a lot of small holes with a soldering iron, and then enjoy the pouring drops. Children really like such water procedures.

But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.

And to make a stationary shower, you must first pour water into a tank or barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water here warms up well, and you can wash yourself plenty. To be able to do this in cooler weather, then it is necessary to provide a heating system in such containers.

Do-it-yourself country shower

Before installing it, you need to make a shower cabin. If possible, you can make it out of wood by placing this small structure on the base. Put in a wooden door or go with a shower curtain like this.

There are more simple options. If you have oilcloth, then use it.

Another option is to purchase impregnated fabric or use an old awning or tent.

If you made a fence from corrugated board and you still have materials, then try to make a shower for giving from them. metal pipes you need to dig in according to the markup, pour them with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become the roof.

If you have little wooden planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for it will cost almost free.

When the shower is ready, you can install a water tank on it. To make it warm up better, you can make a kind of metal or hose coil. Then the water will warm up more actively.

These and other homemade products for giving allow you to make the most of the available containers.

To be able to get warm water even when it is not heated by the sun, use electric heating. To do this, you can position the plastic barrel vertically or horizontally. Then it will be necessary to mount the ten on one side, and on the other? water inlet fitting. Make an overflow hole so that excess liquid flows out, and you can see that the container is already full.

Now it remains to install the tank. Usually, a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a soul canister from a metal or iron barrel. If you need to heat the water, then a heating element is mounted in the barrel.

Check out other examples of what can be done on personal plot with your own hands.

Interesting homemade products for giving with your own hands

Garden tools are very necessary for working on the ground. Often in the store they sell not very high-quality sets. After a short use, the handle of the shovel breaks off, or the teeth of the chopper are bent. Therefore, if possible, try to make tools with your own hands.

Take:

• cutting;
• fragment of a water pipe;
• scrap from a two-handed saw;
• screws;
• screws;
• fragment profile pipe section 3 cm.

Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut a piece of pipe, unbend the sector, and in the place where the stalk will be, you need to work with a hammer to give the future chopper the desired shape.

To make a blade, take a piece of a two-handed saw and draw the outlines of a future chopper. Punch two holes.

At the same distance and the same diameter, you need to make 2 holes on the chopper itself, and then cut out a fragment from a two-handed saw.

Drill these holes with a drill and a drill designed for metal work. Connect these two parts with rivets, which are screws.

Now drill a hole in the top of the chopper to attach the handle here.

Make also a scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to get a very durable set of tools.

Saw off the desired piece of the handle with a grinder and begin to unbend its part with a chisel.

Then, helping yourself with lever tools, straighten this part almost completely.

It remains to work with a hammer so that the scoop blade acquires the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.

Using an abrasive wheel, clean the edges of the shovel and make them more even. Now process the tool with an emery petal wheel. That's how shiny this shovel will become.

Also drill a hole in it for the handle, then insert it and secure with a screw.

Cover the cuttings of both tools with an antiseptic, and then with varnish. Now you can use the tools for their intended purpose. If you want, follow the same principle to make a cultivator for beds.

It is very exciting to create such things for giving with your own hands. Maybe after you make the tools, you want to make a device on which you can dry part of the harvest. See how one gardener did it.

How to make a dryer for fruits and vegetables?

See what materials you need to take for this:

• sheet metal;
• square pipes;
• locking mechanism;
• polycarbonate sheet;
• self-tapping screws, screws;
• 2 door hinges.

But what tools you need to arm yourself with:

• grinder;
• welding machine;
• drill;
• stationery knife;
• tape measure and marker;
• scissors for metal;
• hacksaw.

First you need to make the basis for the drying cabinet. Make a frame out of square pipes. Horizontal and vertical posts are sawn off so that the edges are even. And the ends on the connecting elements should be beveled.

The door here will be metal. To make it, cut 4 fragments from an iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal, using screws with nuts and self-tapping screws. If possible, weld a steel sheet. To make a mount for baking sheets, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 wooden blocks for 4 baking sheets.

An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it dries, put this blank on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, in extreme cases, steel. These materials conduct heat well.

Now you need to sheathe the dryer from the outside, make the roof transparent, made of polycarbonate. Then the sun's rays will penetrate well here. You can also use glass. Cover the ventilation windows with mosquito nets to keep insects out.

Attach hinges and a locking mechanism to the door. Fasten the door in place. See what a wonderful beautiful and roomy dryer turned out.

It remains to make the opposites. They must be breathable. First, knock together the frames from the bars, and then attach a metal mesh to them.

Now you can cut fruit and watch how your device will work. Put a thermometer in the dryer to monitor the temperature. It should be in the range of 50-55°C. At lower temperatures, cover the lower openings by placing a rag here.

In such a home-made dryer, you can dry not only fruits, but also vegetables, herbs, fish, meat, roots.

If this diagram of the device of such a device seemed complicated to you, then you can make a dryer out of metal barrel. A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.

So that water does not flow here and there is better ventilation, such a roof is installed on top.

You can upgrade this fixture with a fan and an electric heater inside.

If you want to make a lawn mower with your own hands, then this is also possible.

Turn an old washing machine into it, for example, like this one.

And if you still have an old bedside table, then you will make a platform out of it for a future almost self-propelled device. But you only need a door from the nightstand.

Drill holes in the center of the motor shaft. Make a cutting knife from an old two-handed saw. It is necessary to saw off from it to the size of the desired shape, cut a recess inside.

Attach two wooden pickets that will become the handles of the mower. Do not forget to fix the motor and extension cord to it. Now you can experience such an interesting unit.

If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.

Lots of interesting ideas waiting for you in the first video.

And with cool homemade products from plastic pipes you can get to know each other if you watch the second story.

Do-it-yourself drawings of homemade products for summer cottages and gardens will be useful to everyone. A dacha is the ultimate dream, if not of any average person, then of every second person for sure. Not everyone, of course, will be lucky enough to become the owner of suburban area, but those who are still lucky need to constantly monitor and ennoble it, which requires considerable costs. Do-it-yourself homemade products for summer cottages and gardens help to maintain your dacha in impeccable condition. Today we will tell you a few secrets on how to save money on buying the necessary things for a summer residence and make them at home. Of course, not everyone can do a grader with their own hands or self-propelled guns for a tractor, but most homemade products will definitely come in handy on the farm.

Do-it-yourself variator for a machine

If you need to constantly work behind the machine, then the frequent change in speed leads to wear on the unit and has the additional disadvantage of regularly stopping the machine. As alternative you can use a homemade variator for the machine. It can be made from wood with your own hands, without a significant investment of time and money. Variator cones are made of hardwood, and it is not necessary to use a lathe to make them, you can cut them with a jigsaw at an angle equal to the angle of the cone.

If you will assemble a cone from disks, then they must then be glued or nailed. Ready-made cones are planted deep on metal rods, while they are attached with screws. In order for the belt to move evenly on the machine, roller guides are required. Rollers can be taken from furniture fittings, but if they are not available, ordinary bearings can be used.

An old washing machine is a real treasure

If there is a working engine from washing machine, then this is a very valuable find, since many useful devices in the household can be made from it. The easiest way is to make an excellent emery for sharpening knives, various tools and drills from the engine from the washing machine.

The main problem in the manufacture of fixtures is the fastening of the stone for sharpening on the engine housing itself. In most cases, the whetstone has a hole that does not fit the motor shaft. That is why you need to make a flange that, on the one hand, can be pressed onto the shaft, and on the other, will have a thread, which will allow you to screw in and secure the grinding wheel.

Image 1. Emery device from the engine of an old washing machine.

Experienced craftsmen recommend that beginners use old pipe cuts 32 mm and no more than 20 cm long as a flange. We make a thread on one piece of pipe, which should be 2 times the thickness of the grinding wheel in its length. The other end of the pipe is heated with a soldering iron and put on the shaft. To better hold the pipe, it can be bolted. After that, they take 3 nuts and screw them onto the flange from the side of the thread until they stop, then put on a washer and, finally, a grinding wheel, then again a washer, fix it with a nut. At the end, you can also add a locknut.

The hardest work is done, after that it remains just to fix the engine, but this is a very individual procedure, since it is not known what holes are on the engine from your washing machine for fasteners. Based on them, you need to make a stand, it is best to use small corners, fastening them together and placing emery on a workbench. The final step is to connect the engine to the mains. Look at ready-made version sharpeners you can in the photo, the drawings are also attached (image 1).

Image 2. Grill from the drum of a washing machine.

Homemade products for summer cottages can also be made from other parts of the machine, for example, an excellent barbecue can be made from a drum. Drum in washing machines made of stainless steel, which in itself is important, since the case is very strong and reliable. It is very easy to make homemade products for giving from a drum, you just need to remove it from the body of the machine, but along with the shaft and pulley. We put the pulled-out drum with the hatch up, and with the wheel down. So the brazier is ready, with the help of a grinder, you can, of course, cut the front of the drum or side to make it more convenient to throw firewood, but here it all depends on your free time and imagination. This makeshift brazier looks very neat, while the drum is littered with small holes, which allows air to be evenly distributed over the coals and provide the necessary heat (image 2).

Manual circular saw from grinder

Image 3. Scheme of the device of a circular saw.

Circular in the country - very useful thing, few people know, but you can make it from a grinder. You will have to complete only 2 elements: a sliding stop and an axial handle. After that, you can use your circular saw from the grinder at any time.

2 small pieces of metal corner are suitable as a sliding stop. The edges of the corner are rounded so that they do not catch on the part during processing. The corners are interconnected at the back and front with bolts or nuts. On the body of the above power tool itself, you need to put on a clamp made of metal tape. To the screw tie of the clamp, which will be located below, a double-folded strip of tin or galvanized steel with a hole for the rear bolt of the sliding stop is attached.

In the gearbox of the grinder, we make 4 small holes for the M5 bolts. For convenience, the gearbox can be disassembled first to better see where the hole can be made. These 4 holes are needed in order to attach the handle. The handle can be made from an ordinary metal tube. This manual version of the saw from the grinder is finished, if you want to make a real stationary version of the circular saw, then you will need more skills in work, tools and well-calculated drawings (image 3).

Agricultural equipment and devices

Agricultural machinery is very important tools in the country, without which no owner can do. Agricultural machinery today costs a lot, and you don’t really want to spend a lot of money on a thing that is rarely used, but you can’t do without it. One of the most popular devices is a wheelbarrow, it can be made from improvised means, thereby saving a lot of money. To make it you need:

Image 4. Drawings of a homemade cart.

• wheel, preferably made of rubber;
• plywood;
• 2 corners;
• wooden block, 3 m long;
• nuts and an axle from a bolt.

The technique for making this tool for giving is very simple and will be clear even to a novice master, the main thing here is to measure everything clearly, because if you do it by eye, it will turn out crooked. Wheelbarrow drawings are attached (image 4).

A much-needed tool for suburban area, which in winter will help get rid of snow, that is, a shovel, can also be made from plywood. You will need:

• plywood 10-12 mm thick;
• wooden handle;
• nails;
• steel plate 4-6 cm wide.

Plywood will serve as a shovel bucket, and the timber will allow you to hold the handle. Metal edge the front and back plywood - the future bucket.

A rake is often required to process the garden. To make them, you will need a wooden block 35 by 35 mm. The length of the handle can be cracked at your discretion, but it is not recommended to make it too long, as it will be difficult to use it. In addition to the bar and handle, you need to make at least 4 metal teeth. Metal must be taken durable so that it does not bend to the ground during operation. You can use metal from an old shovel, cut teeth with a grinder. The teeth are leveled with a hammer and holes are drilled for the screws. Then the structure is fixed.

Video about making a do-it-yourself cart:

Garden sprinkler design

Homemade agricultural equipment also includes garden sprinklers, which can be made almost from the waste that everyone has in the house. To irrigate your garden you will need:

• spray;
• rubber hose 3-4 m long;
• plastic one and a half liter bottle;
• pump;
• wooden or metal stick of any length, but the longer the better.

The sprayer is screwed to the top of the stick with a nozzle so that the lever is pressed with the help of nylon threads. Tape firmly so that the sprayer does not move. After that, we take a plastic bottle and use a hot nail to melt a hole in the neck. Then we push the bolt into the melted hole and fix it with a nut from the outside.

Before inserting the bolt, drill a through hole in it with a simple 3 mm metal drill. The hose is put on a bolt and secured with a small clamp using a screwdriver. We attach the second end of the hose to the pump and again fix it with a clamp so that everything is airtight.

Poison is collected in the bottle for spraying beetles or water for watering the crop. Screw the container to the top of the spray gun, which is attached to a stick. Next, with the nozzle closed, we pump up the pump a little, after that we unwind the nozzle, and the sprayer starts working. In this way, you can spray trees of any height and large beds, if necessary, you can simply put the device on the ground and pump up the pump from time to time.

You can even make small greenhouses from a film in the country, you only need to drive a metal rod or stick into the ground and fix a plastic film in the form of a cone on the base.

Video about the drip irrigation system using a plastic bottle:

From below, the film is fixed in a circle from old barrel or set with stones.

Conclusion on the topic

Now you know how to make expensive tools for a summer cottage without a significant investment of money, time and nerves. The main thing is not what you use to improve your site, but the fact that you should like the work and stay in the country should bring joy.

The dacha is a place to relax the soul and improve the body. Far from the bustle of the city, where the air is clean, it is so nice to actively spend time, grow an excellent crop. And having worked enough, relax as it should!

But to relax in comfort, you need to work a little to create beautiful, useful and comfortable things. Do-it-yourself homemade products for summer cottages and gardens - cheap, reliable and cheerful!

Wooden pallet furniture (pallet)

After the construction of the house, there is a lot of construction debris that can come in handy! Bricks and wall blocks are brought on pallets. They are returnable containers, but it’s reluctant to mess with this issue. With a minimum of effort, you can make an original wooden furniture for giving!

Look at this stylish coffee table for the living room. Do you recognize? It's just a regular pallet! It is not difficult to make such an interior item. Take a coarse sandpaper and clean the surface of the boards from which the container is knocked together. Then you need a finer sandpaper to make the surface smooth. After sanding, carefully wipe off the fine dust, consisting of particles of the removed wood.

Color your new table oil, acrylic or other wood paint. If the pallet was knocked together from decent boards and you like the natural texture of wood, then it is better to varnish the table. For convenience, small wheels can be screwed from below.

More complex products are also made from this container - sofas, chests of drawers, cabinets. See some photos for inspiration.

Agree, this is a chic and stylish headset! If you yourself will make soft seats, sew ribbons of the same fabric to them from below to tie them to the frame. Otherwise, they will move.

The bed and a large headboard for it with shelves are also made of pallets. Good orthopedic mattress will allow even on such original basis sleep well.

This outdoor seating area oriental style will not leave anyone indifferent.

Swing

Do you have children in your family or do you have guests with babies? Then you can't do without a swing! In order not to spend a lot of money, you can use unnecessary things.

For example, you can make an excellent swing seat from an old chair in a matter of minutes by sawing off the legs. And to make it beautiful, paint it with fresh paint.

By the way, not only children love to swing. Adults also enjoy it. Look at this version of a swing from a rattan chair, the legs of which have become unusable. Soft pillows of delicate colors, ribbons, lace fabric - everything to create a romantic atmosphere.

If there are large trees in the garden, you can hang such a structure on a thick bough, then you do not need to build complex fasteners, a strong rope will be enough.

The second life of an old bath

There are many possible options. Here are some of them.

Flower garden. One of the most simple ways use an unnecessary bath. It is enough to make good drainage from broken brick or expanded clay at its bottom, add a nutrient substrate and plant plants.

Water. The easiest option is to bury the bath in the ground and pour water into it. But you can decorate it in such a way that no one will guess from what you built yourself a pond in the country. A small fountain, natural stone for framing, lighting and favorite plants will help create a unique corner for relaxing on the site.

Furniture. Yes! It's hard to believe, but the bath turns out to be excellent furniture - sofas and armchairs. And don't worry if your bathtub is cast iron. With the help of a grinder, you can cut out part of the board to make a sofa or chair.

flower beds

Flower beds can be decorated in a very original way.

Vertical gardening with colorful rubber boots. In their soles, make holes for the outflow of excess water and arrange drainage from expanded clay. Fill shoes with soil and plant plants. Remember that any container that is not deepened into the ground quickly heats up in the sun, the earth dries up in it. Therefore, on hot days, water green pets at least 1-2 times a day..

You can also use other shoes.

If there is an extremely unattractive stump from an old tree on the site, which cannot be uprooted, do not be discouraged. It will make an excellent raised flower bed.

Some gardeners love their plant-decorated stumps so much that they even varnish them to slow down the decay process.

Instead of a stump, a picturesque log can serve as the basis.

Flower gardens can be arranged in various used items - suitcases, bags, furniture, tires and even in a car!

Try to make a raised warm bed, framing it with a neat wooden frame, stone or brick.

From plastic bottles

An excellent material for homemade products in the country and the garden with their own hands are plastic bottles. They can perform useful features or be a decorative element to decorate the landscape.

Spray bottle - indispensable assistant in the garden. Make small holes in the container, put it on a pipe or hose with a neck and secure. It remains only to open the tap to let the water flow.

With the help of a bottle, you can organize root watering for plants. Make holes in it. So that the earth does not clog into the holes, put old polyamide tights on the container. Dig in the bottle so that the neck remains above the ground. There you will pour water from a hose or it will fill itself when it rains.

This method of watering will not introduce you into financial expenses at all, but will bring tangible benefits. From the bottle, water will flow gradually in small portions, without falling on the above-ground part of the plants. And this is very important for many fruit and decorative green pets: tomatoes, cucumbers, zucchini ...

Having filled the bottles with water, you can safely leave for a week in the city, and the plants will not suffer from drought. More water, before it goes to the roots, has time to warm up.

Frame flower beds and beds with glass or plastic bottles.

It looks neat and is practical. If you bury the bottles in the ground, they will become a barrier to the spread of perennial weed roots. And if most of the container remains on top, then you can pour earth inside the perimeter and the flower bed or bed will turn out to be slightly raised. She will be easier to take care of.

Durable wear-resistant panicles are made from plastic bottles. They have an attractive appearance due to bright colors.

Do-it-yourself homemade products for summer cottages and gardens bring special comfort to your personal green corner. They are pleasing to the eye, serve as furniture or are assistants in the struggle for the harvest. And they protect you from all sorts of adversity. After all, it is known that things made with your own hands have a special power.

Let your cottage be hospitable at any time of the year!

It's no secret that today almost any goods for garden plot are expensive in stores. So, for example, to purchase various accessories will cost, as they say - "a pretty penny". And if you make them from scratch, then you will spend no less, because you still have to buy the source materials.

So why not save money and organize do-it-yourself garden crafts from what you usually have at hand, or is it inexpensive? Moreover, everything can be done really beautifully and neatly. Plus, it's functional.

In this article, we will consider the most useful do-it-yourself homemade products for summer cottages and gardens, which are simple and original.

Beautiful "usefulness" for the garden and vegetable garden

It is worth noting one important point- you need to understand that only a small part of the list of crafts that can be done will be disassembled. Just these options are like a start, a “push” for fantasy.

After all, it is important to understand the very principle of how easy it is to organize everything, and then everything depends only on your imagination. So, let's start the review.

Pond from an old bath

If a small reservoir of this type is made on the site, then it will perform several functions at the same time - we will familiarize ourselves with them in the table below.

Agree, the task is worth it to implement it. Moreover, for this you only need old bath, which in most cases is available on the site.

A pond is made according to the following scheme:

1. We dig a hole with our own hands in the right place, which in its parameters should be slightly larger than the dimensions of the bath.

Advice: take the choice of place as responsibly as possible.
It is undesirable to arrange a pond too close to the dining table, for example.
The fact is that various midges, bees, etc. can periodically flock to the water.
And brushing off insects during lunch is not very pleasant, as you know.

1. We lay several boards at the bottom of the pit- They will have a bath.
2. We insert a bath into the pit and level it. We close its drain hole with a stopper. At the same time, it is desirable to treat the outer edges of the cork with silicone so that in the future there will be no leakage of water from the container.

1. We fill with earth all the free space between the metal and the ground.

Well, then it remains only to decorate the structure. To do this, you can lay out beautiful stones around the perimeter or, for example, plant flowers. In addition, you can create an edging from boards or any wooden sheets, panels that are more or less resistant to moisture.

As for filling the tank, for this you can use both water from the central water supply and natural streams. For example, you can bring the edge of the gutter of the gutter system of the house to the bathtub and the pond will be filled with rainwater.

In principle, such homemade products for a garden can be slightly adjusted - use any tank, barrel, etc. instead of a bath.

Now let's look at another very handy craft.

Pallet bench

Surely at some point you will want to sit in the garden - near an artificial pond, for example. And here you will already need such a useful design as a bench.

Buying a new product is expensive. It is much easier to make a bench from a pallet - if it is not available, then, as a rule, a considerable amount of them is thrown out near large warehouses and industries.

The bench is made quickly.

1. Make a transverse cut on one side of the pallet to the left of the reinforcing bars.

1. On the other side, perform exactly the same operation, only on the other side of the bars.

1. We divide the product into two parts.

1. We insert blocks of bars between the boards, as shown in the figure below. We get the back and seat.

1. We fasten the wood with self-tapping screws at all connecting points.

1. We put the remaining wooden elements under the seat and use them to adjust the height.

As you can see, everything is quite simple. Now you can paint the bench and mount other homemade products for the garden and cottage.

Now consider a very functional, original and cheap craft.

A hanger is a very necessary element. After all, you can hang not only clothes on it, but also a considerable part of various garden tools.

Of course, the “primitive” version of this design is ordinary nails or self-tapping screws. However, it looks rather nondescript, and besides, the nails tend to gradually loosen inside the holes into which they are hammered.

And loosening means that such "hooks" will periodically fall to the ground. We offer a more original and reliable solution - to make a hanger from an old rake.

All you need is the metal part, no wooden handle. Even if such an element is not available in the sheds, then acquiring it in the nearest market is not a problem. The price of a rake is acceptable for everyone.

The hanger is mounted like this:

1. We tie the wire to the two edges of the line on which the teeth are fixed. In this case, a piece of wire should be one. That is, it turns out that the fasteners, in fact, resemble the way paintings or mirrors are hung on a string.
2. We drive a large nail into the wall or in any desired place and hang a rake on it.

The hanger is ready - you can hang anything on the teeth of the rake: shoulder blades, caps, etc.

Now let's apply the old shoes, which are usually a lot in the country.

Flower pots from shoes

The ideal option is the presence of rubber boots, but in principle, regular leather shoes will do.

From such shoes you can make non-standard flower pots that fit perfectly into the style of almost any garden.

The scheme of work is as follows:

1. We nail or fasten the boots with screws to the fence or to any other suitable plane.
2. We fall asleep in each boot the earth.
3. We make several holes in the soles - they are needed to release excess water.
4. We plant flowers in pots and enjoy the appearance of the invention.

Note!
Any garden homemade products with your own hands can be "improved" indefinitely.
The main thing in this business is to correctly organize the “basic” thought, idea.
And you can decorate the invention with anything and as your heart desires - there are no restrictions.

Keep this simple rule in mind when planning "utilities" for your garden.

This concludes our review of useful and original crafts for a garden plot and summarize the article.

Output

As you can see, gardener's homemade products are quite simple, and you can make them from almost anything. We hope that this article will be a catalyst for your ideas, and you will be able to beautifully decorate your site. Well, if you want more information on this topic, we recommend that you also watch the video in this article.

Summer is the time when most people, escaping from the bustle of the city, want to go to nature. Probably every resident of a stuffy metropolis is familiar with the picture, when train stations and commuter trains are packed to capacity with people who want to get out of the stuffy city closer to nature, to their country estates, where they can rest their soul and body, and also do useful work. For most people, a dacha is not just a place to relax, because it is here that you can do gardening, grow vegetables and other crops, and also realize your potential as a landscape designer! And, do-it-yourself homemade products for home and summer cottages on our website will help you with this.

Thus, it becomes clear that a dacha is not an easy place to relax from the bustle of the city, because for an experienced summer resident there will always be some interesting activity, for example: do-it-yourself crafts for giving. Among creative, enterprising and resourceful people, there is an opinion that sitting around is a waste of time. It is for this category of "workaholics" that do-it-yourself homemade products for summer cottages and gardens are not only a way to pass the time and improve your own site at no extra cost, but also an excellent method of realizing your hidden potential.

The section “do-it-yourself crafts for giving and gardening” is intended for people who believe that the cottage is intended not only for recreation, but also for active and generally useful work. Crafts for home and summer cottages, which are presented in this section of our portal, are easily made by hand from improvised means that are present in the arsenal of every experienced summer resident. Who would have imagined that even ordinary country garbage could turn out to be a real masterpiece of modern "country" culture!

In order to make the homemade products presented from the section for giving and gardening, it is enough to have a standard set of tools and non-standard thinking, a desire to do something useful, as well as minimal skills in reading blueprints and following instructions. Country crafts from improvised materials and construction waste are one of the most tempting options for saving extra money that can be spent on something more substantial. Moreover, the money saved can be spent on landscaping a suburban area or arranging a workplace to create new crafts.

Thus, it becomes clear that with a minimum ability to work with hands and understand the drawings, everyone can afford to create anything for a summer residence: build and decorate the house itself or a change house, develop their own unique interior elements or ennoble old furniture, make an impromptu bath or steam room . And with a well-functioning fantasy, you can create decorations for a garden or vegetable garden, organize a home-made system automatic watering the same garden, as well as protect the vegetables growing on it from the effects of pests. And all this, do-it-yourself homemade products for summer cottages.

Thus, you can be sure that the cottage, in itself, is a blank canvas on which a skilled worker, like a real artist, can realize a huge number of useful things and creative ideas. Especially if "dacha" creativity and physical work with the use of brains brings pleasure, special pleasure. Yes, and the realization that this or that functional device is made by hand, at minimal monetary cost, you see, cannot but warm the soul.

In fact, a dacha is a piece of personal space where you can safely try to realize your most daring and extraordinary ideas, without fear of falling into awkward situation. And the very fact that such crafts can save you from unnecessary costs for the purchase of an expensive garden equipment or expensive decorations for the site, it simply cannot but warm the soul. In the section "useful homemade products for giving with your own hands", the editors of our portal have collected the most daring and unusual design solutions and functional ideas that can form the basis of the unique and inimitable development of this or that addition to the site with the help of your own ingenuity. Build a playground? Easily! Do you need a greenhouse or a greenhouse to grow vegetables, but do not have extra funds? You can assemble them yourself! Expensive fencing can hurt family budget? No problem! With the help of interesting ideas posted on our portal, these problems can be solved absolutely free of charge!

Thus, the old motivating slogan "If you want to do something well - do it yourself" is gaining more and more relevance. After all, if you can do something with your own hands, then why go to the store for it and spend extra money that may come in handy in the future? With a certain amount of knowledge, unnecessary trash will turn into a multifunctional device or an excellent addition to a country interior or garden design.

Doing something with your own hands is not only pleasant, but also extremely useful, because, as you know, a developed person should be developed in everything. And when work brings pleasure, then doing something will not be difficult! Have a nice and productive holiday, summer residents! We hope that our homemade products for summer cottages and at home will help you in the household.