How to properly connect the washing machine to the sewer. How to connect the drain hose of a washing machine to the sewer: methods and rules for draining

During installation and connection washing machine, the problem arises of how to organize the discharge of waste water correctly. The best way is to connect drain hose directly to the sewer branch, but it is also the most time-consuming. We will describe how to organize the drain in detail and start with the preparatory work.

We prepare tools and accessories

Any serious work requires careful preparation, connecting a washing machine to a sewer is no exception. If you have to install old car after moving, organizing water drainage, you may need some tools and accessories, and when installing a new machine, some of the accessories are already included in the application with the machine.

But you need to start preparing by determining the installation site. There can be three options:

  1. In the bathroom, which is very convenient, since any outlet, including a drain, is practically at hand.
  2. In the kitchen next to the sink.
  3. In the hall.

Having determined the place, prepare the tools so as not to look for them by organizing a diversion. May be required:

  • various screwdrivers;
  • keys;
  • pipe cutter, if necessary, cut into the drain pipe;
  • welding for metal-plastic pipes;
  • siphon ordinary or with a check valve;
  • plastic tee;
  • silicone sealant;
  • sealing rubber;
  • corrugated drain hose of the required length if the factory one is too short.

Note! Docking hoses is not recommended, as additional connections are additional risks of water leaks. The optimal length of the hose is no more than 3 meters, because the longer the hose, the greater the load on the pump, the drain should be closer.

Another step in preparing the washing machine for connection is this. When the machine is fully prepared for connection to communications, you can proceed to the main work.

Ways to connect to the sewer

Before organizing the drainage and connecting the washing machine to the siphon, it is necessary to install the siphon itself on the sink. If the siphon does not have a separate outlet under household appliances, then a plastic tee will also need to be connected to it. With this connection, an unpleasant odor from the sewer can enter the drum, where the laundry lies after the washing cycle.

Therefore, it is necessary to organize an "air barrier" in the siphon. For this, the siphon has a special branch to which a corrugated pipe is connected. It is bent in such a way that water stagnates in its bend, creating a reliable plug that does not let smell from the sewer into the tank of the machine. At the same time, such a plug does not impede the removal of waste water from the washing machine to the drain and is updated with each discharge of water into the sewer.

Instead of a simple siphon, you can use a siphon with a check valve, which prevents not only smell, but also waste water from entering the machine, in which case it is much more efficient to organize the drain. If the siphon is clogged, a situation may arise when the wastewater fills it and flows back into the machine by gravity. To prevent this from happening, a valve is built into the siphon.

After installing the siphon, you need to connect the hose to the branch from the siphon. This is easy to do, just fasten the clamp.

In some cases, the drain hose of the washing machine is connected not through a siphon, but into a branch sewer pipe. In this case, an O-ring is required. Such an adapter will allow you to insert the hose into a wide hole in the pipe. This method is more labor intensive than the previous one. However, it is reasonable to use it when the washing machine is placed at a distance of more than 2 m from the sink siphon.

The photo shows a direct connection without using an adapter siphon tube (left) and using it (right). Such an adapter allows you to create an air congestion, which prevents odors from entering the sewer into the machine.

When organizing the draining of waste water from the machine through a siphon or directly, the distance from the floor to the drain point must be taken into account. The point at which the end of the hose will be located must be at least 50 cm from the floor. The maximum height from the floor to which the drain hose can rise is no more than 100 cm. These figures depend on the capacity of the drain pump.

Connecting the drain hose of a washing machine through a siphon or directly to the sewer is considered the most reliable way to organize a drain. The risk of water leakage is minimized if the hose is accidentally touched. In addition, from an aesthetic point of view, it is also best option, since the hose is usually hidden behind the machine itself or the kitchen set.

Other ways to drain waste water

Most simple options to organize the drain of water from the washing machine, it is to throw the drain hose through the sink, bathroom or toilet. To do this, you need a plastic hook-shaped nozzle that will hold the hose on the sink or bathtub.

A similar way to organize a drain is the most unreliable. And it has a number of disadvantages:


Important! If, nevertheless, it is decided to use this method of draining water from the machine, then remember that the length of the drain hose should not exceed 4 meters, since a larger volume of waste water can remain in the hose itself and stagnate in it, emitting an unpleasant odor.

Thus, you can connect the washing machine to the sewer yourself, if you have the desire, tools and time. And you should not save on components, because reliable and competent connection- this is the key to trouble-free and uninterrupted operation of the washing machine.

In the process of installing the automatic washing machine you purchased at the place of its permanent operation, the problem immediately arises of supplying all the necessary communications to it, including the following types of connections:

  • draining dirty water;
  • connection to the cold water supply system;
  • connection to the electrical network.

In this article, we will look at how the washing machine is connected to the sewer. different ways.

Ways to connect to the drain line

The connection of the washing machine with the drain of the apartment highway can be done in two different ways: one of which involves the temporary organization of the drain, and the second is stationary.

With a temporary connection option, the waste water outlet is fixed on the edge of the sink or bathtub. In this case, the hose must be fixed on the edge of the selected container in such a way as to exclude the possibility of its accidental fall.

The stationary option involves inserting into the existing drain system by attaching an additional siphon to it, which avoids the leakage of unpleasant odors from the sewer.

The vast majority of users, of course, choose a stationary connection option, in which in some cases it becomes necessary to extend the drain hose. Its maximum length (limited, as a rule, by the power of the built-in drain pump) is usually indicated in the instructions attached to the washing unit.

Note! Some experts advise leaving a small gap at the junction of the drain with the siphon, which excludes the possibility of “sucking in” water and “freezing” the operating system of the machine when performing certain operations. In doing so, there must be one required condition, consisting of the following: the location of the air gap should be slightly above the level of the permissible rise of water in the sink or bathroom when their drain is clogged. Otherwise, water may leak through this "bleed" gap.

Connection order

You can, of course, entrust the most important operations related to connecting a washing machine to employees of specialized services that can organize their fast and high-quality implementation. But if you have certain skills, the option of independently connecting the washing machine to the drain line is not excluded. Consider the difficulties that you may encounter when connecting yourself.


  • The second reason for the undesirability of this type of drain connection is the possibility of distribution bad smell from the sewer through the washing machine (this does not happen if there is a siphon).
  • In order to prevent water from pouring out of the washing device by gravity, its drain hose must be at a height of about 0.6 meters from the base of the floor. For these purposes, a special mount is provided on the back wall of the machine, from which the hose is drawn down, and then again rises to the siphon.

And in conclusion, we will consider the features of connecting a washing machine to a sewer in a private house (where sewerage, as such, is most often absent). If you do not have a special sewer system- draining is organized in the simplest way called "overboard".

Note! When organizing the drain "overboard" it is not allowed to use a hose longer than 4 meters. With a longer hose length, an amount of water will accumulate in it, commensurate in volume with the water supply in the machine itself, which will lead to its constant leakage from the system (regardless of the height of the hose on the back wall).

Video

Find out what consumables will be needed to connect the washing machine.

When installing a brand new washing machine in his apartment or private house, each owner is worried about how to properly connect it to communications. And if we already wrote about how to connect the machine to the water supply and, now it's time to consider connecting the washing machine to the sewer.

The surest technology is to connect the drain hose directly to the sewer. The process requires effort and time, but we will tell you in detail how to properly connect the drain hose of the washing machine.

Connecting the washing machine: preparation

Any work related to technology requires serious and thorough preparation. And connecting a washing machine to the sewer is no exception.

If the washing machine is old, and you just reinstall it after moving, then you will have to buy something. Some accessories are included with new machines.

Preparation includes three stages:

  1. Decide on a place. It can be a bathroom - you must admit, it is convenient, since the drain is very close. The kitchen is also suitable, as the sink and sewerage are within reach. IN rare cases- this is the hallway, when there is very little space in the kitchen or in the bathroom.
  2. Prepare your tools. You may need all or part of the list below:
  • Screwdrivers - slotted and cross, different sizes(it is better to take a universal one with nozzles).
  • If you have to cut into a pipe, then a special pipe cutter will not interfere.
  • Welding for metal-plastic pipes.
  • Siphon for connecting the washing machine to the sewer. Suitable for both regular and non-return valves.
  • Plastic tee.
  • Sealant.
  • Rubber seals.
  • Corrugated hose of the right length to drain the water (buy a new one or lengthen it if what the manufacturer provided is not enough).

Important! The drain hose should not exceed three meters in length so as not to create an unnecessary load on the drain pump.

Remove the shipping bolts holding the tank in place. Unscrew them from the back panel and close them with plugs.

After going through all three steps, you can start connecting the drain hose of the washing machine.

Options for connecting the machine to the sewer

There are three most common options, consider them.

Through the siphon

Before you connect the washing machine to the sewer, you need to install the siphon on the sink. If the siphon does not have another outlet for the technique, then you will need a tee.

But there is one downside! If you connect the washer in this way, then a not-too-pleasant smell from the sewer pipe may enter the drum.

To avoid this, your task is to take care of creating a so-called "air barrier" in the siphon.

Examine the siphon - on it you will find a small hole for a corrugated pipe. This pipe is bent so that when water stagnates, a “plug” appears in the bend. It is this cork that does not let sewer aromas into your machine.

Such a scheme does not complicate the discharge of water, and the plug is “updated” during each descent of waste water into the sewer system.

Through siphon with non-return valve

If you have purchased a siphon with a non-return valve, you can be sure that the washing machine is protected not only from odors, but also from contaminated water. With it, the drain will be much more efficient.

During the occurrence of a blockage in a conventional siphon, the wastewater returns to the machine on its own - the so-called “self-draining” process takes place. To protect the machine from this, you should choose a siphon with a valve.

Attention! After installing the siphon, connect the hose to the appropriate branch using a clamp.

without siphon

It happens that the connection occurs without a siphon - directly to the sewer pipe. For such a case, you will need to buy an adapter seal ring. It allows you to insert a thin hose into a fairly wide hole. The method is more complicated, but it will be relevant in two cases:

  • There is no sink in the room.
  • The machine is more than two meters away from the sink siphon.

In the photo you can see a visual demonstration of how to properly connect the washing machine to the sewer system without using a siphon adapter tube. It also shows how to connect the SMA through a siphon.

In any case, no matter how you organize the drainage of the washing machine - through a siphon or directly to the pipe, consider the distance between the drain point and the floor. The point at which the end of the hose must be located according to all the rules must be at least 50 cm from the floor and not more than 1 m.

Of course, the numbers may vary, given the power of the pump: the more powerful the pump, the greater the deviation from the norm.

The considered withdrawal methods are considered one of the most reliable. They will protect your home from leaks, and the aesthetic issue has been resolved - the hose is neatly hidden behind the machine or in kitchen set. Simple, harmonious, reliable.

Other ways to connect the washing machine to the sewer

But there are also not quite traditional ways to connect the washing machine - they are extremely simple.

You can throw the hose through:


All you need in this case is a small plastic hook with clips to hold the hose.

Although the method is simple, it cannot be called reliable. Here are a number of disadvantages that you may encounter by choosing it:

  • If the water pressure is strong, the hose may come off and water will flow onto the floor. The hose is attached so weakly that it can be torn off by a careless movement. Also, children or pets can “help” him fall.
  • After each wash cycle, the bathroom, toilet or sink needs to be cleaned and washed.
  • There is no mention of aesthetics. Washing dishes where water has just drained after washing is at least not very hygienic.

Please note! If such a drain suits you, then do not buy a hose longer than 4 meters. If the hose is too long, not all of the water will drain, but remain in the tube, wasting not too pleasant odors.

Now that you know all the schemes for connecting the machine to the sewer pipe, it remains only to choose the appropriate method and easily organize the drain. If you go the traditional way, do not save on components, and then your washer will thank you for years of flawless and trouble-free operation.

And the video will help you do everything right:

Our parents still remember those times when doing laundry took all day, or even the whole weekend. Today, for these purposes, a special household appliance is used, which is in every home. It has replaced manual labor and saves a lot of time. In modern technology, every detail is extremely important, including the drain hose for the washing machine.

Drain hose for washing machine and its types

The drain hose (sleeve) performs one task - it diverts dirty water after washing and rinsing things into the sewer. If your appliances are not equipped with a wastewater outlet, or you want to replace the drain hose for the washing machine, its price will be from 30 to 1300 rubles. The final cost will depend on the length of the drain and the specific model of household appliances.

There are three types of drain devices on the plumbing market:

    Standard drain hose. Its length is from 1 to 5 meters. If necessary, it is built up with a second similar one using a plumbing clamp.

    Telescopic drain hose. Got wide use due to the fact that it fits almost all modern car models. Its folded length is 60 cm. When stretched, this figure reaches two meters. Disadvantages of this type of drain hoses:

    • high vibration during draining;

      clogged more often

      cracks and breaks may appear.

  1. Drain hose in the bay. The length of the bay from the manufacturer is 50 meters. It consists of modules soldered together. You just need to measure the required length and cut along the notch. The length of a single module is 50-55 centimeters. The neck is usually made of steel. The use of a very long hose of this type leads not only to the appearance of dirty water stagnation zones, but even to blocking the drain. In addition, such a tube is easier to damage or deform.

Drainage sleeves are made of gray dyed polypropylene. At the ends there are special connectors (19 and 22 mm). From the washing machine, the drain hose is connected to the sewer. If the tubing cannot be connected to a drain, secure it to a sink or tub.

What is the length of the washing machine drain hose?

Think about how you will drain from the machine to the sewer. Use a tape measure to measure this distance. The drain hose is available at all points of sale of household goods and household appliances.

In such stores, hoses of different lengths are sold: from 1 to 5 meters, as well as modular drain hoses.

As we have already said, modular hoses are sold in large coils and consist of segments of 0.5 meters. You just have to contact the seller to measure and cut off the sleeve of the required length.

However, modular hoses are not always easy to find, so we advise you to opt for other types of hoses.

So, you came to the store to buy a drain hose for the washing machine. How to do it right? Remember that when choosing a drain device, you should not be guided by the principle - "The stock pocket does not pull!" and buy the longest hose. The shorter the length, the easier it is for the drain pump to pump water from the washing machine to the drain. If possible, install the automatic machine so that the distance to the drain does not exceed 3.5 meters.

How to install a drain hose for a washing machine

If you still need a longer hose, then buy two hoses and use a connector. As a rule, this is a short plastic tube, the ends of the drains are placed on it and pulled together with clamps.

In a situation where the diameter of the drain hose of the washing machine is different from the diameter of the extension, try to connect the end extending from the washing machine to the end of the tube that has a larger value of this indicator, using a plumbing adapter with different numerical parameters at the ends - 19 and 22 mm. When connecting hoses of identical diameter, use a standard 22 by 22 mm connector.

Such an adapter can be easily made by yourself from a rigid PVC tube of the desired size. It will be no different from what is sold in stores. Tighten the hose clamps on the connector.

To start washing, an automatic machine needs water that enters the tank technical device from the central water supply. There are also alternative ways to deliver it to start the cycle. At the end of washing, the used liquid is removed using a special device, which, as a rule, is supplied with the appliance. Connecting the drain hose of the washing machine is a common procedure. There are two ways to organize the removal of dirty water from the tank:

    Temporary, using the special plastic bracket supplied with the machine. The drain is attached to the edge of the sink or bathtub.

    Stationary, connection to the drain directly inset. A plastic guide is needed here to prevent the drain hose from kinking, which can lead to blocking the drain.

Washing machine users often prefer the second installation option. With this method of connecting the drain hose of the washing machine, it is invisible, does not spoil general form bathroom. With it, the situation is completely excluded when the hose was simply not fixed on the edge of the sink or bath, and after the end of the wash cycle dirty water descends to the floor.

Follow the recommendations of experts before installing the drain hose for the washing machine yourself. How to fix? What is the height of the washing machine drain hose? Does the washing machine have a drain hose check valve? All these points are very important, and compliance with installation standards will help prevent possible breakdowns of expensive equipment.

    check valve mounted on modern models washing machines, passes water in one direction. If it is not there, a certain height for fixing the drain device must be observed. Usually allowable height, on which the drain is installed, is indicated in the instruction manual for the automatic machine. Failure to follow the recommendation may result in damage.

    The extension of the drain hose of the washing machine is used in case of insufficient size of the existing sleeve, when it is problematic to bring its end to the sewer outlet. However, as with buying a tubing that is too long, the same principle applies: if the tubing is too long, the suction pump will work harder and may not be able to do its job, which will also lead to its breakdown and costly repairs.

    Regardless of how you fixed the drain - temporarily or permanently, its end should not be immersed in water.

How to connect a drain hose to a washing machine through a siphon

To drain dirty water through a siphon located under the sink, you need to replace the existing one with a special one for an automatic machine. Such siphons have the necessary pipes to which drains are supplied, including a drain hose for a washing machine. Place the siphon at a sufficient height to form a water seal that prevents the smell of sewage from entering the room and the reverse flow of water.

Install the purchased siphon, tighten the connections. Check the assembly for reliability by running water. Then connect the drain device to the pipe using a plumbing coupling and a rubber cuff that does not allow the connection to leak and does not allow odors from the sewer to enter the room. Or take a special adapter for the drain hose of the washing machine, tighten the connection with a clamp for tightness.

The organization of the drain with a siphon (fixed connection) will not interfere with taking a bath or washing yourself using the sink during washing. If the water is drained into a sink or bathtub, then this possibility is excluded, since the bathtub will fill with dirty water after the end of the wash cycle. Washing in the sink, into which the used liquid is drained, will also not be very pleasant.

Please note that the siphon must be installed strictly vertically. Horizontal installation is unacceptable, as this method threatens to leak. The height of the organization of the drain is also important. The bend of the special plastic bracket, in which the drain device is fixed, must be at least 60 centimeters from the floor level.

Another interesting solution related to connecting the drain to the siphon is siphons for hidden installation into the wall. One side is used to connect to sewer pipes, the other - to supply drain hoses. Contacts are also sealed with a collar or cuff. In the immediate vicinity, a tap is mounted to connect to the source cold water. With this solution, the connection process (even when replacing the old washing machine with a new one) will take no more than 5-10 minutes.

How to connect the drain hose of the washing machine to the sewer without a siphon

Draining is not difficult to do directly, without a siphon. You will need a sewer tee and a rubber cuff to seal the connection. The device must be inserted into the cut of the sewer pipe and the drain must be connected to its outlet through the cuff. It is possible to bring the sewer pipe to the washing machine and connect it directly to the hose. Create a bend in the hose in front of the sewer connection, separating the tank of the machine from the sewer system. This insulates against unpleasant odors. Carry out sealing of connection .

If the drain is left straight, without an S-curve or rise, odors from the sewer can freely enter the drum of the washing machine, where the washed, clean linen lies. Instead of bending, it is better to use the same siphon, which is guaranteed to cut off any "flavors". And in order to prevent wastewater from accidentally falling back into the tank, use an anti-siphon - a check valve.

How to extend the drain hose of a washing machine

Together with the new washing machine, the manufacturer provides everything necessary accessories for its connection to the water supply and sewerage system. However, the standard equipment does not take into account the individual layout of your home and does not always meet the requirements of the buyer. The most common problem of this kind is a short drain hose.

The standard length of the drain device that comes with the machine is 2 meters. If it is not enough, then you can use a washing machine drain hose extension, which is purchased separately at a plumbing store. In addition to this device, you will also need a connector and metal clamps, through which you will ensure the necessary tightness.

There are several ways to extend the drain hose to the required length:

    If an adapter is used for extension, then it can be a thin-walled rigid PVC tube with an external size of no more than 20 millimeters and metal clamps of a suitable diameter - no more than 27 millimeters to seal the connection.

    To perform a “hidden” installation of a drain system (when the extension cord needs to be hidden in a wall or in a floor screed), a metal-plastic pipe up to 3.5 meters long and 20 millimeters in diameter is best suited.

    Another practical and simple option for extending the drain is a compact telescopic tube. It will provide a reliable tight connection without kinks and folding.

    You can also use the usual corrugation of standard length - up to 2 meters.

Remember important rule regarding the maximum drain length? That's right, its size should not be more than 3.5 meters! If this length cannot be limited, then it is better to move the machine closer to the drain than to build up additional meters of hose.

Before you begin the seemingly simple process of sleeve extensions, check out the standard guidelines. Consistent implementation of the points of this recommendation will allow you to avoid offensive mistakes and guarantee a good result.

Work execution algorithm:

    Before starting work, make sure that all the right materials is in stock, and if necessary, purchase the missing accessories. If there is no pipe of the required diameter on sale, then buy one whose diameter will be as close as possible to the existing one and use an adapter.

    Disconnect the machine from the mains. Attach the ends of the existing drain hose and extension to the connector, the contact point is marked with a special risk, made exactly in the middle of the tube.

    Create a tight, airtight connection using clamps. Do not overtighten the clamps, you may damage the tube.

Before using the machine for the first time, check again how well the joints are sealed. If necessary, put the ends of the hoses on a special sealant. Inspect the installation site of the drain hose, make sure that there are no objects with sharp edges, protruding interior reliefs, on which it can be rubbed or damaged.

Replacing the drain hose of a washing machine without problems

Models of automatic equipment differ from each other, therefore, the place where the drain sleeve is fixed in them also differs. But there are universal rules on how to change the drain hose in a washing machine, relating to all types.

    If the wash cycle was turned on, then wait until the end of the program, make sure that the washing machine drum has completely stopped. Disconnect the machine from the mains. Fix the wire in the grooves on the back of the washing machine so that later it does not interfere with your work.

    Disconnect the water supply hose from the water supply system. When unscrewing it, be careful not to lose the sealing rubber ring. Detach the drain sleeve from the sewer pipe and close the sewer outlet with a special plug. Mount the drain and supply tubes on the back of the washing machine so that the free ends look up. The preparation phase has been completed.

    How to remove the drain hose of a washing machine? The drain tube comes out of the bottom or top of the rear wall of the machine, but in order to remove it, we need to get to the pump. Raise top cover device. You will see that the sleeve is connected to the pump. Disconnect it from the pump and from the machine body and carefully remove it. Pay attention to the shape of the old device. Sometimes manufacturers use an L-shaped drain hose for a washing machine. The bend, as a rule, is located in the area of ​​\u200b\u200bthe pump, that is, inside the machine itself. You may have difficulty finding and purchasing an identical sleeve. If you can't find a replacement, don't despair, use L-shaped tips, which are definitely sold in a plumbing store, and a standard drain hose.

    Pour out the remaining water from the hose. Proceed with the installation of the purchased drain in reverse order. Follow the manufacturer's instructions carefully.

How to clean the drain hose in the washing machine

Often the malfunction of the washing machine is provoked by contamination in the drain hose. It gets clogged during the operation of the equipment. A suspension of dirty soapy water settles inside, in which fabric fibers, wool, and hair come across.

You can clean the drain hose of the washing machine. How to implement this, we will consider below.

For cleaning, the drain hose is completely disconnected from the washing machine. The sequence of actions depends on the model of the device, the method of attaching the sleeve to the water drainage system.

Record actions using a photo or video, this will help not to get confused during assembly and will come in handy for subsequent repairs.

First of all, unplug the washing machine from the mains. Shut off the water supply pipe. Drain the remaining water from the drum through the drain filter. Disconnect the hose from the sewer system, if there is water left in the drain hose of the washing machine, drain it.

To detach the second end of the sleeve, you will need a set of screwdrivers and pliers.

Consider the drain hose disconnection diagram for LG, Indesit, Ardo, Ariston, Samsung, Candy, Beko, Whirrool washing machines:

    Detach the bottom panel by unscrewing the screws with a screwdriver (in some models, the bottom is bolted or missing).

    Remove the screws holding the filter.

    Lay the washing machine on the side wall, after laying something under it (this will protect the floor and the machine itself from scratches). Before that, screw the transport bolts holding the drum of the washing machine into the corresponding holes on the back wall.

    Open the clamp with pliers. Disconnect the drain hose from the pump and the washing machine body.

To disconnect the drain hoses for Zanussi and Electrolux washing machines, disconnect back wall. You need to do the following:

    Release the latches holding the drain hose;

    Unscrew the hose that supplies water to the washing machine;

    Unscrew the bolts fixing the top cover, remove it;

    Unscrew the bolts holding the wall, remove it;

    Using pliers, open the clamp on the drain hose and disconnect it from the drainage system.

The design solution for German-made washing machines involves disconnecting drain hoses for Bosch, AEG, Siemens washing machines after removing the front of the housing:

    Remove the detergent drawer from the housing;

    Separate the bottom panel of the case;

    Remove the clamp that secures the cuff;

    Disconnect the cuff;

    Unscrew the bolts fixing the front wall;

    Unscrew the bolts fixing the lock of the locking mechanism or gently move the wall, reach out and disconnect the cable leading to the lock;

    Slightly lift the front wall up and pull towards you to remove it from the hooks;

    Loosen the clamp, carefully remove the drain hose.

All the methods considered apply to front-loading washing machines.

In machines with top loading, the drain is disconnected through the side wall. For this:

    Unscrew the bolts holding the side wall;

    Remove the panel;

    Open the clamp and pull out the drain hose.

The drain hose is cleaned with a thin Kevlar cable ( synthetic fiber). A small brush at the end of such a cable will remove dirty soap deposits from the inner walls of the sleeve. To do this, perform the following algorithm:

    Pass the cable through the hose several times from both ends;

    Remove the cable and bring one of the hose holes under the water jet;

    Fix the drain in its original place;

    Reassemble the washing machine in reverse order.

To improve the result, pour any anti-scale or citric acid into the detergent tray, start the wash cycle at a temperature of 60 ° C.

To prevent the occurrence of blockages in the drain, it is recommended:

    Using a special laundry bag;

    Adding water softeners along with detergent;

    Carrying out preventive cleaning from scale;

    Use of washing powder for automatic washing machines;

    Checking clothing pockets for small items.

Where to buy a drain hose for a washing machine that does not have to be changed often

It would seem that the answer to the question is obvious - drain hoses can be purchased at any plumbing store! But not everything is so simple. Among the huge range of goods on sale, there are a lot of products of low or frankly low quality.

Often the decisive factor when buying a particular hose is the price. It is logical to assume that the higher it is, the better the hose. This is partly true, but you still need to know the criteria for choosing a good product.

Alas, special markings and marks on the conformity of the goods to GOST are not always a guarantee of the quality of the product. The market is full of counterfeit products. It is better to choose a hose “by touch”, that is, when choosing it, you should check how it sits on the pump nozzle. If the fit is loose, but it does not hang out, then you have chosen the right product. You should refrain from buying too "tight" sleeves, as they are usually unreliable and there is a high probability of damage during installation.

It is best to buy hoses, bends, tees and sewer pipes from the same manufacturer. Then problems with correct fit all components of the system will not arise. And it is better to buy everything as a set, and not to buy more later. This will be the main guarantee of quality and reliability.

Speaking of guarantees. You should purchase goods only in trusted stores, from sellers who are really suppliers of real manufacturers.

However, it is not at all necessary to look for manufacturers of drain hoses for washing machines on your own, because we have done it for you. We present to your attention the company "SantekhStandard", which specializes in the sale of such products. In its assortment only those products that are approved the best specialists firms and passed GOST R.

In the company's catalog you can find drain and inlet hoses "Aqualine", having a length of 1 to 5 meters inclusive and a connection size of 3/4". These products are manufactured in Russia.

In addition to drain hoses, the catalog contains a range of only those products that are guaranteed to fit together. Accessories are available for sale polypropylene pipes, shower hoses, fittings, sealing materials and much more. When purchasing plumbing and products for sewerage and heating systems from the SantekhStandard company, you can not worry about the quality and compatibility of the purchased products.

Specialists of the company "SantekhStandart" are ready to help both individuals and companies choose plumbing. All you need to do is call:

For the correct and trouble-free operation of the washing machine, it is necessary to properly connect the washing machine to the sewer. You should know, first of all, that when choosing a place to install a washing machine, you must take into account the length of the drain hose. It is also necessary to take into account the diameter of the sewer pipe when leading it to the washing machine. The diameter of this pipe is 40 mm miniaml.

For the correct and trouble-free operation of the washing machine, it is necessary to competently sewer. You should know, first of all, that when choosing a place for it is necessary to take into account the length of the drain hose and the connection diagram. It is also necessary to take into account the diameter of the sewer pipe when conducting it to. The diameter of this pipe is 40 mm miniaml.

Draining the washing machine: connection to the sewer

After completing the stage of work on bringing water to the machine, we will consider several basic options for connecting the drain of the washing machine. In any case, this issue should be taken seriously, because when the water is drained by the machine, the hose can pulsate strongly and the unreliability of the connection can cause water leaks, which can significantly spoil the mood and property not only for you, but also for the neighbors below.

Option 1. With the help of the clamp that usually comes with the washing machine, you can secure the drain hose to the side of the tub or sink. In this case, the possible height of the hose must be taken into account. It is indicated in the installation and operating instructions, usually manufacturers recommend that it does not exceed 100 cm. Otherwise, the pump power may not be enough to drain all the water. In addition, it makes sense to provide a rigid fastening of the latch, for example, to a water tap.

Option 2. The second way to connect the washing machine to the sewer is to connect the drain hose directly to the siphon. In this case, you get rid of the need for additional cleaning of the sink or bathroom at the drain.
What is a siphon? This is a curved tube through which water from the sink enters the sewer. The bend is necessary to create a water blockage, which prevents the penetration of an unpleasant odor from the sewer pipes.

There are several types of siphon designs. The simplest is a conventional flexible corrugated pipe. A special clamp is used to fix the knee. The advantages of such a siphon include low cost and ease of installation, so it can often be found in new homes.

The second, most common type of siphon is a bottle siphon. It is equipped with a special flask in which a water jam is created. In addition, if you accidentally drop the ring into the sink, it will linger at the bottom of the flask.

When organizing the drain of the washing machine, you can use special siphons, which are equipped with additional outlets for drain hoses. They can be purchased at a hardware store. When correct installation siphon, you will get a neat connection to drain the washing machine directly into the sewer. It is worth noting that this work often requires appropriate skills and its solution should be entrusted to a qualified plumber.

Option 3. You can lay an additional elbow from the existing sewer pipe, where the sink is drained. In this case, an additional set of sewer pipes with a coupling and a reducer is required, which acts as an adapter from the drain hose to the standard sewer pipe. All connections must be strong, for this it is advisable to coat them with plumbing silicone.

Connecting and installing a washing machine

Installation and connection of the SMA consists of several operations:

Remove shipping bolts, place the machine on a firm, level surface, level the machine.

Connecting the washing machine to the mains. If you recently had a renovation, or you live in a new building, most likely you already have a special outlet for SMA, then there is no problem. If not, then you will have to pull a separate line from your electrical panel without fail. This is the most time-consuming and expensive operation in the entire installation procedure. You will need a circuit breaker 16A, a wire with a cross section of at least 1.5 square meters. mm., a waterproof euro socket with a grounding terminal, and, accordingly, lay and install all this.
Connecting the washing machine to water. Here you need a special tap - with a ½ x ¾ thread, or an angled or through passage, depending on the specific conditions. If the apartment has a separate water outlet for connecting the washing machine, a corner tap is installed, if not, a passage tap is installed in the break of the water outlet for cold water and flexible supply to the mixer, or the toilet barrel. If there are no filters in the apartment coarse cleaning water, it is advisable to install the filter in front of the water supply tap to the washing machine. Next, a supply hose is connected to the tap. If the supply hose is equipped with an aquastop device, it is recommended that it be positioned vertically. If the length of the supply hose is not sufficient, it can be extended using special materials.

The next step is to connect the washing machine to the sewerage system. There are two main ways. Connection to the siphon of the nearest plumbing fixture ( kitchen sink, washbasin, etc.) in this case, the siphon is changed to a special one with a branch for a washing machine. This method has a significant drawback - if the siphon is clogged, dirty water from the washing machine will flow into the sink. However, this is a very common way. Another way to connect the washing machine to the sewer is to install a tee directly into the sewer system. This method is more preferable, does not have the disadvantage described above, but is slightly more expensive for the consumer.

And the last stage is a test run. The performance of the machine is checked, without linen, with a small amount of powder, at the same time it will be washed. It is enough to fill in water, stop the program, turn on the drain, check all connections for leaks.

washing machine connection automatic washing machine motor connection diagram washing machine connection price Processed

Liked the article? Share it
Print article
Top